Group 3 base oil is the base liquid of a lubricant, treated with hydrogen so deeply that the shape of its molecules changes: it ends up with almost only stable molecules, and its thickness changes little with temperature. It almost always comes from crude oil, but in Brazil the ANP (Agência Nacional do Petróleo, the oil regulator) rule for labeling counts it among synthetic base oils. It suits oil that must start in the cold, evaporate little and last in the heat, such as engine oil.
What is Group 3 base oil?
It is the most treated of the three groups of base oil that come from crude oil, and what sets it apart from Group 2 is one thing only: its thickness changes less between cold and heat.
One step back. Every lubricant has two parts: the base oil, which is most of the bottle, and the additives, ingredients in small doses that give the oil an extra quality. Think of a cake: the base oil is the batter; the additives are the baking powder and the sugar.
The American Petroleum Institute (API), the petroleum association of the United States, sorts base oils into groups. There are five groups, defined by what the oil contains (Group III, in Roman numerals, is the same as Group 3):
Groups 1, 2 and 3: usually refined from crude oil, each one more treated than the one before.
Group 4: PAO (polyalphaolefin), built in a reactor from small molecules.
Group 5: everything else, such as most naphthenic oils (a type of crude oil product), esters and vegetable oils.
Group 3 has the same minimum purity as Group 2: almost only saturated molecules and almost no sulfur. Saturated molecules already carry all the hydrogen they can hold, so they react slowly with the oxygen in the air. The article on Group 2 base oil shows how the hydrogen treatment reaches that result.
The thickness has a name: viscosity, the oil's resistance to flowing. Honey has a lot; water has little. The viscosity of Group 3 changes less when the temperature rises or falls. The guide to what base oils are explains refining and the groups from the beginning.
The limits for saturates, sulfur and viscosity index (the number explained in the next section) come from API 1509 (Annex E). In Brazil they apply through ANP Resolution 911/2022, and the section on the certificate, further down, gives each one.
Why does the viscosity index set Group 3 apart from Group 2?
Because it is the number that shows how much an oil's viscosity changes with temperature, and it is where Group 3 goes beyond Group 2.
Think of honey taken out of the fridge: it barely leaves the jar. Warmed in the microwave, it pours easily. Every oil does the same: it thickens in the cold and thins in the heat; what differs from one oil to another is how strongly.
That strength became a number, the viscosity index (VI). The higher the VI, the less the oil changes between cold and heat.
An example shows the effect. Take two base oils with the same viscosity at 40 °C, the temperature at which the ISO VG grade is measured, the number in the name of the finished lubricant.
The one with the higher VI gets a little thicker when the machine warms up, which helps hold the oil film, the thin layer that keeps metal parts apart. At a cold start, it is much thinner than the other, and the oil reaches the parts sooner.
Figure 1. Two base oils with the same viscosity at 40 °C: in the cold, the one with the higher VI runs much more easily; in the heat, it is a little thicker.
Why does the grade not show this difference? Because it is measured at one temperature only, and the VI compares two.
For those who need the number: the ISO VG grade (ISO 3448, explained in the article on what ISO VG means) is the viscosity at 40 °C. The VI comes from the viscosities at 40 °C and 100 °C (ASTM D2270; in Brazil, NBR 14358). An additive, the VI improver, raises the VI of the finished oil; the API limits apply to the pure base oil.
If both come from crude oil and have the same minimum purity, where does the higher VI come from?
How is Group 3 base oil made?
It goes through the same three hydrogen steps that make a good part of Group 2, with the first one more intense, which changes the shape of more molecules.
And shape decides the VI. Oil molecules are made of carbon and hydrogen, with the carbons linked to each other in two ways. In a chain, the carbons form a long string, as in paraffin; in a ring, the string closes into a wheel. Many molecules have both: a ring with chains attached to it.
A chain molecule changes little in viscosity with temperature, and a ring molecule changes more. The more rings become chains, the higher the VI.
Group 2 has already been through hydrogen: the treatment removes sulfur and nitrogen and turns aromatic rings (rings that still lack the hydrogen they could hold) into saturated rings. Group 3 goes further in the same steps.
The three steps, in order:
Hydrocracking. Hydrogen under high pressure and heat, helped by a catalyst (a material that speeds up the reaction without being used up), breaks large molecules and opens part of the rings, which become chains. The more intense the step, the more chains and the higher the VI.
Wax isomerization. In the cold, long straight chains stack into crystals and become wax, and the oil stops flowing. A catalyst rearranges the carbons of these chains and creates short branches on them. A branched chain does not fit against its neighbors and stays liquid: straight pencils line up side by side in a box, twigs with short branches do not. The wax becomes oil instead of being removed, and the VI stays high.
Hydrofinishing. A last pass with hydrogen, milder, saturates the last aromatics and the other molecules that still lacked their full hydrogen. The oil gets lighter in color and more stable to light and heat.
Figure 2. From crude oil to Group 3. Hydrofinishing, the third step, saturates the little that is left and does not change the picture. The same steps make a good part of Group 2; in Group 3 the hydrocracking is more intense.
Figure 3. In the cold, straight chains stack up and become wax; chains with short branches do not fit together and stay liquid.
The result is an oil with almost no aromatics, with more chains and fewer rings than Group 2, and many of those chains branched.
For those who need the name: step 2 is catalytic dewaxing by isomerization (hydroisomerization), different from the other catalytic dewaxing, which cracks the wax and removes it from the oil.
It remains to see what the machine gains from an oil like this.
What does Group 3 gain inside the machine?
It gains three things, each with its own cause: it starts better in the cold, evaporates less and, with the right additive, lasts longer in the heat.
Cold start. With a high VI and the wax transformed, the oil thickens less on a cold morning, reaches the parts sooner and the pump suffers less. In a car, the starter motor turns more easily.
Low evaporation. Think of an uncovered pot on the stove, losing water. Hot oil also loses its lightest molecules, which turn to vapor; the level drops and the oil that stays gets thicker. At the same viscosity, Group 3 usually evaporates less than Group 2. The reason is shape: to give the same viscosity, a chain molecule has to be larger than a ring molecule, and a larger molecule takes longer to turn to vapor.
Life in the heat, with one condition. A saturated molecule reacts slowly with oxygen. With almost no sulfur, however, Group 3 loses a protection that Group 1 still has. Being less treated, Group 1 keeps part of the sulfur of the crude oil, and that sulfur slows the reaction with oxygen. Group 3 depends on the antioxidant (an additive that slows the oil's reaction with oxygen) chosen by the formulator. With the right antioxidant, it usually lasts longer in the heat than Group 2 and Group 1.
Figure 4. At the same viscosity, the Group 3 molecule is larger and takes longer to turn to vapor: it usually evaporates less.
That is why Group 3 appears in low-viscosity engine oil, automatic transmission fluid, hydraulic oil, long-life circulating oil (the kind that runs in a closed loop between the machine and the tank) and industrial oil that works over a wide temperature range.
For those who need the name: evaporation is measured by the Noack method (ASTM D5800) and cold start by the CCS simulator (ASTM D5293; in Brazil, NBR 14173).
With so much transformation, one question comes up most often on the label.
Is Group 3 oil synthetic?
It depends on who classifies it, and all three answers hold at the same time:
By origin, it almost always comes from crude oil, like Group 2.
The API classifies by composition, and the words mineral and synthetic are not part of the definition of the groups.
In Brazil, the ANP has a rule for the registration and labeling of lubricants that counts Group 3 among the synthetic base oils, alongside PAO and other bases made in a reactor.
In the United States, in 1999, the advertising self-regulation body decided, in a case between two manufacturers, that an engine oil made with Group 3 could be advertised as synthetic. The market followed the decision, and since then a lot of oil labeled "synthetic" contains Group 3.
For the buyer, the consequence is direct: two oils with "synthetic" on the label may have a Group 3 or a PAO base, so ask for the group. The difference between synthetic, semi-synthetic and mineral oil in the finished lubricant has its own article.
For those who need the number: ANP Resolution 804/2019, art. 4, item XI (synthetic base oils: Groups III and IV, synthetic esters, polyglycols, polybutenes, alkylated naphthalenes and others). ANP Resolution 911/2022, which specifies base oil, does not use the words mineral and synthetic. The 1999 case was decided by the NAD (National Advertising Division).
What is the difference between Group 3 and Group 3+?
Group 3+ is a market name for Group 3 that usually has a higher VI and evaporates even less. The API and the ANP do not define this class, and in the official table it remains Group 3; with no standard for the plus sign, there is also no official VI for Group 3+.
The difference comes from two routes:
a wax-rich feedstock, such as wax separated in the refinery itself or wax made from natural gas (the GTL route, gas to liquids), isomerized as in step 2 above, which gives an oil with chains almost all branched;
an even more intense hydrocracking.
For the buyer, the rule is short: the "3+" in the quote proves nothing; only the certificate of quality of the batch (the producer's document with the analysis results) does. The section on how to check the group shows how to read it.
At Kelpen Oil, we distribute HBP-E III PLUS, a Group 3+ base oil obtained by wax isomerization, for those who formulate engine oil.
All this purity has a price when it is time to formulate.
What should you watch for when formulating with Group 3?
The main concern has a name: solvency, the oil's ability to keep other substances dissolved, and Group 3 has less of it than Group 2.
The rule is "like dissolves like": many additives and residues dissolve better in an oil that has rings, especially aromatic ones. With fewer rings and almost no aromatics, Group 3 dissolves even less than Group 2. The article on paraffinic, naphthenic and aromatic oil compares the solvency of each family.
This brings three consequences:
Additive. Part of the additives dissolve poorly and may turn cloudy or separate in the cold and in long storage. That is why the additive package (the set of additives in the formula) is tested in the Group 3 itself, and not only in the Group 1 or 2 base oil the formula was made with before.
Seal. The rubber seal ring that has lived for years in a Group 1 oil, with aromatics, swells a little, and the machine counts on that swelling. In Group 3 it may shrink and leak after the change. Coming from Group 2, the risk is lower.
Oxidation residue. Oxidation is the aging of the oil by oxygen. With the right antioxidant, Group 3 forms less sludge (sticky mud) and less varnish (a hard layer on hot surfaces). There is a catch: because Group 3 dissolves less, the residue that forms tends to clump together instead of staying dissolved. The additive package has to keep it spread through the oil so that it does not settle.
The usual fix is to add to the formula a part of Group 5 base, such as ester (a synthetic made from acid and alcohol) or alkylated naphthalene (another synthetic that dissolves well). Both bring back solvency; the ester also brings back the seal swelling.
There is also a limit in extreme cold. Even with the wax transformed, Group 3 thickens and stops flowing before PAO does; in a freezer room and in a start far below zero, PAO is usually the choice.
For those who need the number: solvency is compared by the aniline point (ASTM D611); the higher it is, the less the oil dissolves. Seal compatibility is evaluated by ISO 6072, in hydraulic fluids, and by ASTM D7216, in engine oil.
Before formulating, though, comes the question of whoever receives the base oil: is what arrived really Group 3?
How can you tell if a base oil is really Group 3?
By the certificate of quality, the document with the analysis results that, under ANP Resolution 911/2022, accompanies the tax document for each load of base oil sold.
Three fields decide the group:
saturates: 90% or more;
sulfur: 300 ppm (0.03%) or less;
viscosity index: 120 or more.
Look at the VI first, because it is the only one of the three whose limit changes from Group 2 to Group 3. With a VI below 120, the base oil is not Group 3, whatever the name says.
The VI on the certificate is that of the pure base oil: the ANP rule forbids adding additive to the base oil sold, and the additive that raises the VI goes only into the finished oil. So a finished oil with a high VI does not tell you the group of its base.
Figure 5. The certificate shows the batch result; beside it, the Group 3 limit (API 1509). The viscosity index is the field that sets Group 3 apart from Group 2.
At Kelpen Oil, we distribute Group 3 base oils, from the HBP-S line, for formulating high-performance engine oil and industrial oil. We also formulate finished lubricants, including Group 3 ones.
Our own laboratory in Arujá (SP) checks the batches, and no batch is released without approval. Saturates and sulfur come from the certificate of the base oil producer: the laboratory does not measure saturates, and its sulfur test (ASTM D6481) starts above the Group 3 limit.
| What we measure | What it reveals in a Group 3 base oil | Standard |
|---|---|---|
| Viscosity at 40 °C and 100 °C | The viscosity of the batch and the two points for calculating the VI | ASTM D7042 |
| Viscosity index | Whether the base oil reaches 120 | NBR 14358 |
| Pour point | The lowest temperature at which the oil still flows; shows how far the wax was transformed or removed | NBR 11349 |
| Viscosity in the cold-cranking simulator (CCS) | How much the oil resists the turning of the engine at a cold start | NBR 14173 |
| Aniline point | The solvency of the batch; in Group 3 it is usually higher than in Group 2 | ASTM D611 |
| Carbon distribution (CA, CN, CP) | How much of the carbon is in aromatic rings, saturated rings and chains; in Group 3, almost all of it is in chains and saturated rings | ASTM D2140 |
The article on the lubricant analysis laboratory shows how these tests are done.
For those who need the number: API 1509, Annex E, Table E-1; ANP Resolution 911/2022, art. 7, which forbids adding additive to the base oil sold.
Knowing what it is and how to check it, what remains is choosing in which formula it is worth paying for.
When should you use Group 3 base oil?
Group 3 pays off when the oil works over a wide temperature range, must evaporate little or stays a long time in the hot machine. In steady, warm service, Group 1 or Group 2 are usually enough.
| If the lubricant you formulate… | Base oil | Why |
|---|---|---|
| Works at a steady temperature, with no cold start (typical hydraulic and gearbox oil, the gear reducer) | Group 1 or Group 2; Kelpen Oil distributes Group 2 from the HBP-I line | In that condition, the VI of both is enough |
| Is high-performance engine oil, transmission fluid or long-life industrial oil | Group 3, HBP-S line | Group 3 combines high VI and low evaporation |
| Faces extreme cold (freezer room, start far below zero) | PAO (Group 4) | It flows at a much lower temperature than Group 3 |
| Must dissolve a lot of additive or resin | Group 1 or naphthenic | Their solvency is higher |
| Must be very thick | Bright stock, the thickest base oil of Group 1 | It gives high viscosity to the blend |
All the base oils we distribute are on the page of base oils for lubricant producers.
Frequently asked questions
Is Group 3 the same as hydrocracked oil? Not always. Hydrocracking also makes Group 2; what puts a base oil in Group 3 is the measured result, with a viscosity index of 120 or more and the saturates and sulfur limits met. That is why the word "hydrocracked" in a quote does not replace the certificate.
Is Group 3 suitable for industrial oil? Yes. It goes where the oil works hot for a long time or over a wide temperature range, such as hydraulic oil and long-life circulating oil, with the antioxidant chosen for it. The HBP-S line is also recommended for industrial oils.
Can you mix Group 3 with Group 2 or with PAO? Yes: all of them are oils of saturated molecules and they blend well. The blend has intermediate properties; the formulator blends to balance cost, VI and cold behavior, and checks the finished oil in the laboratory.
Is Group 4 base oil better than Group 3? It depends on the condition. The Group 4 PAO flows at a much lower temperature and, at the same viscosity, usually evaporates less; its VI is close to that of Group 3+. It costs much more, and in a good share of engine and industrial oils Group 3 delivers what is needed at a lower cost.
Glossary
Antioxidant: additive that slows the oil's reaction with oxygen.
Hydrocracking: step in which hydrogen under high pressure and heat, with a catalyst, breaks large molecules and opens part of the rings, which become chains.
Viscosity index (VI): number that tells how much the oil's viscosity changes with temperature; the higher it is, the less it changes.
Wax isomerization: step in which a catalyst creates short branches on long straight chains, and the wax becomes oil that stays liquid in the cold.
Saturated: molecule that already holds all the hydrogen it can and so reacts slowly with oxygen.
Solvency: the oil's ability to keep additives and residues dissolved.
Viscosity: the oil's resistance to flowing; honey has a lot, water has little.
Talk to the Technical Team
At Kelpen Oil, we have been a reference in base oil distribution since 1999. The Kelpen Oil Technical Team evaluates the application, the temperature range, the cold-start requirement and the additive package and recommends the base oil among Group 2, Group 3 and Group 3+. If the oil is already in use, the laboratory in Arujá (SP) does the used oil analysis, as a paid service.
Ask for the certificate before the next purchase: if the VI does not reach 120, it is not Group 3, whatever the name in the quote.




